![]() The one you will need is under the VR section. When creating the sequence, you will see a collection of different presets. Next, open Adobe Premiere and create a new project. Once you've confirmed your settings, press "Next" and wait for the trim to export with the desired format and settings. Do note: by enabling either of these, you will be unable to use your GoPro Max's " 360 Audio" option. To maintain a consistent horizon line, even when the camera itself is rotating, enable 'Horizon Level'. If you wish to lock your camera's orientation to the world and minimize rotation, enable World Lock. It's recommended to export at the highest resolution, 5.6K, using CineForm (on Windows) or Apple ProRes (on Mac). Click the scissor icon once more.Īfterwards, click the check-mark button below to confirm your new trim and then select "Export Trim".įrom here, you may configure your export settings, selecting your resolution, codec, as well as additional options. ![]() From there, drag the timeline and the icon to where you wish your footage to end. Drag your timeline to align the scissor icon to where your footage should start. You will see a similar blue icon appear on your timeline. Here you will be able to pan around (by clicking and dragging the footage with your mouse), scrub through the timeline, lock the horizon and world orientation of the footage, as well as trim and export your footage.Īs an example, if you would like to trim out yourself starting/ending the recording, click on the scissor icon below the timeline. Open the 360 file using the GoPro Player. Drag it onto your machine, and into an accessible folder. If you are on a Windows machine, you will also need the HEVC plugin installed. In order to view it, you will need the GoPro Player application. The footage you're looking for will be in a. First find your connected GoPro device, and navigate through its directories until you reach where your footage is stored ( GoPro MAX > GoPro MTP Client Disk Volume > DCIM > 100GOPRO). Now, you will transition over to the computer. The screen on the GoPro Max will let you know when a USB connection is detected.Īlternatively, if you have a microSD adapter, you can manually take out the microSD and insert it with the adapter into the computer. The USB-C end will go into the GoPro Max while the USB-A into your computer or device of choice. Take the USB-C to USB-A cable and connect the camera to your computer. Your GoPro Max camera will need to remain on. After you have captured your desired footage, click the button again and the recording will stop. ![]() You will see blinking red lights on both sides of the camera while recording is in process. Once done, click the record button (red circle) at the top, and the GoPro Max will begin its recording. If you wish to film a 360 video then tap the bottom left corner icon and switch to 360 Video mode, otherwise you will film a flat 1080p video. Once activated, the screen will light up and you will primarily control, configure, and operate the camera using the touchscreen. If you're looking at the screen, it will be on the left side. Turn on the GoPro Max camera by pressing and holding the power button on the side. Once they're lined up, insert the thumbscrew and tighten until the camera is secured in place. Pull those out.īack to the tripod, place the flaps below the GoPro Max into the two gaps of the tripod adapter. Looking at the bottom of the camera, you will find two flaps with holes in the middle. You will need to attach the GoPro Max to your tripod setup. Once they have been removed, take the two lens protectors, and snap them on over the lenses. Do be careful as they can be difficult to pry off. Next, take the flat gray lens caps off of both sides of the GoPro Max. Ensure the batteries are charged and ready. Included in the GoPro Max pack is a dual battery charger. Ensure that your GoPro has a microSD inserted and that it has a charged battery. Second, find the small cloth sack and take out the GoPro Max and the two lens protectors. This is what will lock your GoPro Max to the weighted monopod. It has two gaps, with a thumbscrew going through it. The adapter is a shiny plastic piece that can be screwed in top of your monopod/tripod setup. From there, attach the tripod adapter piece on top. Afterwards, attach the monopod body (the extendable pole) onto the counterweight. USB Type-C to USB Type-A Cable for Charger x1īelow is the GoPro Max package you would receive from the EDC:įirst you will need to set up your monopod, with the counterweight twisted on the top.This article will go over how to capture 360-degree video footage using the GoPro Max, taking the footage into an editor such as Premiere, then finalizing and exporting your 360 video project.
0 Comments
Leave a Reply. |